N54 Powerdome: Tunes Aspirazioni Downpipes Intercoolers Exhausts Popoffs and co.

[3diablo3]

Io consiglio Bardhal.... ....nettamente superiore a Castrol negli ultimi tempi....

[lukelukes]

Io consiglio Bardhal.... ....nettamente superiore a Castrol negli ultimi tempi....

con l'età la memoria mi inganna.....eppure ricordo che molti decretavano l'xpr royal purple perfetto per l'n54+

[enrita]

con l'età la memoria mi inganna.....eppure ricordo che molti decretavano l'xpr royal purple perfetto per l'n54+

ho trovato questo SIB relativo all'errore delle Vanos.

SI B11 02 08
Engine October 2010
Technical Service

This Service Information bulletin supersedes SI B11 02 08 dated August 2010.

designates changes to this revision

SUBJECT
Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME


MODEL
E82 and E88 (1 Series) with N51, N52K and N54 engines produced from 1/2008

E90 and E91 (3 Series) with N52 engine produced from 3/2005 through 6/2006

E90, E91, E92 and E93 (3 Series) with N51, N52K and N54 engines produced from 7/2006

E85 and E86 (Z4) with N52 engine produced from 1/2006

E83 (X3) with N52K engine produced from 9/2006

E60 and E61 (5 Series) with N52, N52K and N54 engines produced from 3/2005

E70 (X5) with N52K engine produced from 10/2006

E71 (X6) with N54 engine produced from 1/2008


SITUATION
The “Service Engine Soon” (MIL) lamp is illuminated and a power reduction is clearly perceptible. This situation can occur after driving for some time with the engine already at full operating temperature. If the ignition is cycled, the engine then usually performs normally.

The following faults are stored in the DME:

2A82 VANOS intake – stiff; jammed mechanically

2A87 VANOS exhaust – stiff; jammed mechanically

3100 Boost-pressure control, deactivation – boost-pressure buildup prohibited (N54 only)

CAUSE
The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. When the engine operation requires that the VANOS quickly advance or retard the intake or exhaust camshaft, fault 2A82 or 2A87 may be set if the camshaft is “late”, or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 can also be set in the DME fault memory as well.

PROCEDURE

Perform all applicable test plans for the faults stored. A mechanical restriction or electrical failure of the VANOS solenoid and/or the electrical circuit can cause insufficient oil supply to the VANOS assemblies as well. If the results of the test plans are inconclusive then proceed to step 2.



The oil filter cap insert may have been inadvertently removed during the vehicle’s last oil service. If this insert is not installed, it will result in non-filtered engine oil being supplied to the engine, thus possibly clogging or damaging the VANOS solenoids.


Replace both VANOS solenoids and change the engine oil and filter. Drive the vehicle to verify effectiveness. If this repair is inconclusive and the fault returns, continue to step 4.

If the oil filter cap is found intact, it is possible that the camshaft hook ring seals (3) have worn a groove into the camshaft bearing ledge (1), causing a drop in oil supply to the VANOS unit.



Camshaft bearing ledge

Intake camshaft

Hook ring seals



Note the deep grooves worn into the intake camshaft bearing ledge by the camshaft hook ring seals.



Acceptable camshaft bearing ledge – minor wear marks from the rotation of the camshaft are normal.

If the oil filter cap insert is found to be missing, then the entire oil filter housing cap must be replaced (refer to the EPC). If excessive wear to the camshaft bearing ledge is found, it is only necessary to replace the camshaft hook ring seals and the affected camshaft bearing ledge.

[3diablo3]

Interessante... ...però non ho capito cos'è questo inserto tappo che può essere stato rimosso inavvertitamente durante un tagliando:

The oil filter cap insert may have been inadvertently removed during the vehicle’s last oil service. If this insert is not installed, it will result in non-filtered engine oil being supplied to the engine, thus possibly clogging or damaging the VANOS solenoids.

Ma che modello di bmw monta l'N55???

[Franzzz]

Intende dire che hai girato senza filtro olio (magari qualche meccanico si scorda di metterlo ma e' una possibilita' remota)

Le Vanos si inceppano infatti per olio troppo usato o sporco
Purtroppo il filtro e' in carta e va cambiato molto spesso e se si rompe i detriti fanno cacao....

[3diablo3]

Intende dire che hai girato senza filtro olio (magari qualche meccanico si scorda di metterlo ma e' una possibilita' remota)

Le Vanos si inceppano infatti per olio troppo usato o sporco
Purtroppo il filtro e' in carta e va cambiato molto spesso e se si rompe i detriti fanno cacao....

CHiaro.... ....ucciderei se un meccanico non mi cambia il filtro olio!!! Ma il problema non si pone dato che faccio io! Io comunque, cambierei olio max ogni 10.000 km su questo motore...

Chissa se un giorno abbineranno le doppie VANOS con il valvetronic...

[enrita]

chiaro.... ....ucciderei se un meccanico non mi cambia il filtro olio!!! Ma il problema non si pone dato che faccio io! Io comunque, cambierei olio max ogni 10.000 km su questo motore...

chissa se un giorno abbineranno le doppie vanos con il valvetronic...

n55

[MuCcIo]

ho trovato questo SIB relativo all'errore delle Vanos.

SI B11 02 08
Engine October 2010
Technical Service

This Service Information bulletin supersedes SI B11 02 08 dated August 2010.

designates changes to this revision

SUBJECT
Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME


MODEL
E82 and E88 (1 Series) with N51, N52K and N54 engines produced from 1/2008

E90 and E91 (3 Series) with N52 engine produced from 3/2005 through 6/2006

E90, E91, E92 and E93 (3 Series) with N51, N52K and N54 engines produced from 7/2006

E85 and E86 (Z4) with N52 engine produced from 1/2006

E83 (X3) with N52K engine produced from 9/2006

E60 and E61 (5 Series) with N52, N52K and N54 engines produced from 3/2005

E70 (X5) with N52K engine produced from 10/2006

E71 (X6) with N54 engine produced from 1/2008


SITUATION
The “Service Engine Soon” (MIL) lamp is illuminated and a power reduction is clearly perceptible. This situation can occur after driving for some time with the engine already at full operating temperature. If the ignition is cycled, the engine then usually performs normally.

The following faults are stored in the DME:

2A82 VANOS intake – stiff; jammed mechanically

2A87 VANOS exhaust – stiff; jammed mechanically

3100 Boost-pressure control, deactivation – boost-pressure buildup prohibited (N54 only)

CAUSE
The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. When the engine operation requires that the VANOS quickly advance or retard the intake or exhaust camshaft, fault 2A82 or 2A87 may be set if the camshaft is “late”, or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 can also be set in the DME fault memory as well.

PROCEDURE

Perform all applicable test plans for the faults stored. A mechanical restriction or electrical failure of the VANOS solenoid and/or the electrical circuit can cause insufficient oil supply to the VANOS assemblies as well. If the results of the test plans are inconclusive then proceed to step 2.



The oil filter cap insert may have been inadvertently removed during the vehicle’s last oil service. If this insert is not installed, it will result in non-filtered engine oil being supplied to the engine, thus possibly clogging or damaging the VANOS solenoids.


Replace both VANOS solenoids and change the engine oil and filter. Drive the vehicle to verify effectiveness. If this repair is inconclusive and the fault returns, continue to step 4.

If the oil filter cap is found intact, it is possible that the camshaft hook ring seals (3) have worn a groove into the camshaft bearing ledge (1), causing a drop in oil supply to the VANOS unit.



Camshaft bearing ledge

Intake camshaft

Hook ring seals



Note the deep grooves worn into the intake camshaft bearing ledge by the camshaft hook ring seals.



Acceptable camshaft bearing ledge – minor wear marks from the rotation of the camshaft are normal.

If the oil filter cap insert is found to be missing, then the entire oil filter housing cap must be replaced (refer to the EPC). If excessive wear to the camshaft bearing ledge is found, it is only necessary to replace the camshaft hook ring seals and the affected camshaft bearing ledge.

Stessi codici che da la mia ogni tanto di domenica (ogni 3-4 settimane si sveglia). Devo pulire i solenoidi quando ne ho voglia.
Per ora risolvo semplicemente leggendo e cancellando gli errori, e per un mesetto sono a posto di nuovo.

[Franzzz]

180 euro e metti quelle della 1M e sei a posto...

[lukelukes]

la mia è 10/2006 e con la fortuna che mi ritrovo.........